Charging - Versionsgeschichte

Alexanderg: /* Charging station */

2016-06-06T12:43:32Z

‎Charging station

2016-06-06T11:57:30Z

2016-06-06T11:52:02Z

‎Charging station

2016-06-06T11:51:48Z

‎Standby-off / Under-voltage protection

2016-06-06T11:45:11Z

‎Charging station

2016-06-06T11:45:02Z

‎Charging station

2016-06-06T11:44:35Z

2016-06-06T11:43:32Z

‎Charger

2016-06-06T11:43:11Z

‎Charging station

2016-06-06T11:42:54Z

@@ Zeile 63: / Zeile 63: @@
 =Charging station=
-By the help of the perimeter wire loop, the robot finds its charging station where it can be charged again. So, it drives along the perimeter wire (in clock-wise direction) until it detects a charging voltage at its charging pins. There the robot stops and recharges its battery.
+By the help of the perimeter wire loop, the robot finds its charging station where it can be charged again. So, it drives along the perimeter wire (in clock-wise direction) until it detects a charging voltage at its charging pins. There the robot stops and recharges its battery. Due to the standby/charging current, the perimeter sender can detect if the robot is in the charging station and can then switch off the perimeter sender.
 Here you can see the charging via charging station:

← Nächstältere Version		Version vom 6. Juni 2016, 11:57 Uhr
Zeile 1:		Zeile 1:

−	Here you can see the charging without charging station. If you don't want to use a charging station, the charger can be connected directly to the Ardumower.	+	Here you can see the charging without charging station. If you don't want to use a charging station (or for your first tests), the charger can be connected directly to the Ardumower:
		+
	[[File: Ardumower_battery_overview.jpg\|800px]]		[[File: Ardumower_battery_overview.jpg\|800px]]

@@ Zeile 64: / Zeile 64: @@
 By the help of the perimeter wire loop, the robot finds its charging station where it can be charged again. So, it drives along the perimeter wire (in clock-wise direction) until it detects a charging voltage at its charging pins. There the robot stops and recharges its battery.
-Here you can see the charging via charging station.
+Here you can see the charging via charging station:
 [[File: Ardumower_charging_overview.jpg|700px]]

@@ Zeile 35: / Zeile 35: @@
 =Standby-off / Under-voltage protection=
-There are two reasons for a battery switch (standby-off mechanism):
+You can add an undervoltage protection to your Ardumower. There are two reasons for a battery switch (standby-off mechanism):
 Reason1: If the robot was not started within 5 minutes, it should turn battery off to save energy.

← Nächstältere Version		Version vom 6. Juni 2016, 11:45 Uhr
Zeile 65:		Zeile 65:

	Here you can see the charging via charging station.		Here you can see the charging via charging station.
−	[[File: Ardumower_charging_overview.jpg\|~~600px~~]]	+	[[File: Ardumower_charging_overview.jpg\|700px]]

@@ Zeile 1: / Zeile 1: @@
-Here you can see the charging via charging station. If you don't want to use a charging station, the charger can be connected directly to the Ardumower.
+Here you can see the charging without charging station. If you don't want to use a charging station, the charger can be connected directly to the Ardumower.
-[[File: Ardumower_charging_overview.jpg|800px]]
+[[File: Ardumower_battery_overview.jpg|800px]]
 =Charger=

@@ Zeile 11: / Zeile 11: @@
 * Maximum charging current compliance (charging current limit)
-If you are using an existing charger, these things are implemented with high probability already in it.
+If you are using an existing charger, these things are implemented with high probability already in it. If you don't want to use a charging station, the charger can be connected directly to the Ardumower.
 =Total power balance=

@@ Zeile 64: / Zeile 64: @@
 By the help of the perimeter wire loop, the robot finds its charging station where it can be charged again. So, it drives along the perimeter wire (in clock-wise direction) until it detects a charging voltage at its charging pins. There the robot stops and recharges its battery.
-[[File: Ardumower_perimeter.jpg | 400px]]
+Here you can see the charging via charging station. If you don't want to use a charging station, the charger can be connected directly to the Ardumower.
-Here you can see the charging stations contacts:
+<gallery>
 =Videos=